Aluminium sheet made in EN AW 1050 Annealed alloy, with high malleability and transformability, in addition to its intrinsic characteristics of lightness and corrosion resistance, it is a recommended option for all types of decorative cladding and similar applications.
This aluminium sheet with 0.8 mm. thickness is made in alloy 1050 Annealed wich main features are these ones:
The EN AW 1050 aluminium alloy has the following composition under standard EN 573-3:
|
|
Si |
Fe |
Cu |
Mn |
Mg |
Cr |
Ni |
Zn |
Ti |
Others |
Al |
|
|
Indiv. |
Total |
|||||||||||
|
min |
|
|
|
|
|
|
|
|
|
|
|
99.50 |
|
max |
0.25 |
0.40 |
0.05 |
0.05 |
0.05 |
– |
– |
0.07 |
0.05 |
0.03 |
|
|
The mechanical properties of EN AW 1050 alloy sheets annealed according to their thickness and in accordance with standard EN 485-2 are as follows:
|
Condition |
Nominal thickness mm |
Rm MPa |
Rp0.2 MPa |
A50 mm Min. |
A min. % |
Bending radius* |
HBW hardness* |
||||
|
|
|
min. |
max. |
min. |
max. |
180 |
90 |
||||
|
O/H111 |
≥ 0.2 |
0.5 |
65 |
95 |
20 |
|
20 |
|
0t |
0t |
20 |
|
0.5 |
1.5 |
65 |
95 |
20 |
|
22 |
|
0t |
0t |
20 |
|
|
1.5 |
3.0 |
65 |
95 |
20 |
|
26 |
|
0t |
0t |
20 |
|
|
3.0 |
6.0 |
65 |
95 |
20 |
|
29 |
|
0.5t |
0.5t |
20 |
|
|
6.0 |
12.5 |
65 |
95 |
20 |
|
35 |
|
1.0t |
1.0t |
20 |
|
|
12.5 |
50.0 |
|
95 |
20 |
|
|
32 |
|
|
20 |
|
*Reference values for informational purposes.
The difference between the annealed, H18 and H24 states lies in the strength and ductility of the material. The annealed or H111 state is the state with the lowest mechanical strength that the material can have. The H24 state is an intermediate state that balances the strength and transformability of the material, and finally, the H18 state has greater mechanical strength but performs worse in terms of transformability.
The EN AW 1050 alloy has the following physical properties:
|
Elastic modulus |
Coefficient of expansion per ºC (20º-100ºC) |
Thermal conductivity |
Resistivity µW·cm(2) /cm |
|
|
W/mK |
Cal/cm·s·°C |
|||
|
68,600 MPa |
23.5 x 10-6 |
226 |
0.54 |
2.9 |
The general performance of the EN AW 1050 aluminium alloy is as follows in the areas listed below:
– Corrosion resistance: Excellent.
– Weldability: Excellent.
– Formability: Excellent.
– Suitability for anodising: Excellent.
The classification is made in the following range: excellent, very good, good, fair and poor.
The main applications of the EN AW 1050 alloy are as follows:
– Containers in the pharmaceutical and food industries.
– Cladding panels and identification plates.
– Electrical conductors.
– Utensils and trays.
– Reflectors.
